Loading article...
Loading article...
Stream/Area:
-
Subject:
-
Paper ID:
IJSREM68936
Volume:
10 |
11 |
Nov 2026
Pages:
1-7
Publication Frequency:
Monthly (12 issues per year)
License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.
Department of Civil Engineering,
Sanketika Vidya Parishad Engineering College, P.M. Palem, Visakhapatnam – 530041, Andhra Pradesh, India
Department of Civil Engineering,
Sanketika Vidya Parishad Engineering College, P.M. Palem, Visakhapatnam – 530041, Andhra Pradesh, India
The present study investigates the feasibility of using blast furnace slag (BFS), collected from industrial dumping locations in Rajkot, Gujarat, as a complete replacement for natural sand in pavement quality concrete. The work combines material characterization, gradation assessment, mix proportioning for M30, M40 and M50 concrete, fresh and hardened property testing, durability evaluation and field measurements on plain cement concrete pavement panels. The reported average physical properties of the processed BFS were 1.3% water absorption, 2.72 specific gravity and 1.66 kg/cm³ mass per unit volume. Concrete mixtures were designed with 100% BFS fine aggregate replacement and compared with conventional sand mixtures. At 28 days, M40 concrete containing BFS achieved compressive strength of 51.57 MPa and flexural strength of 4.963 MPa, compared with 50.73 MPa and 4.911 MPa for the sand control. Slump values for M30, M40 and M50 were 38, 40 and 41 mm for BFS concrete, respectively. The study also reports lower deterioration under sulphate and sulphuric-acid exposure, positive carbonation-indicator response, satisfactory petrographic observations and broadly comparable temperature-gradient and curling behaviour in field pavement panels. The findings support the technical potential of appropriately characterized BFS as a fine aggregate in pavement concrete. The conclusions remain specific to the source material and experimental conditions examined; chemical composition data and some reported units require verification before specification or wider adoption.
KEYWORDS
Based on the experimental results reported in the dissertation, the following conclusions are drawn: · Rajkot BFS, after characterization and grading, was found suitable for evaluation as fine aggregate. The reported average water absorption, specific gravity and mass per unit volume were 1.3%, 2.72 and 1.66 kg/cm³, respectively; the iron-unsoundness test was reported as passing. · Complete replacement of natural sand by BFS-FA was investigated in M30, M40 and M50 concrete. At 28 days, BFS-FA mixtures recorded higher compressive and flexural strengths than the corresponding sand mixtures in all three grades. · For M40 concrete, 28-day compressive and flexural strengths were 51.57 MPa and 4.963 MPa with BFS-FA, compared with 50.73 MPa and 4.911 MPa with natural sand. · Slump and average density values were slightly higher for BFS-FA concrete. Moisture conditioning of BFS to an appropriate SSD condition is important to limit rapid absorption of mixing water. · Laboratory exposure results indicated comparatively lower mass loss and strength reduction for BFS-FA concrete under the reported sulphate and sulphuric-acid conditions. The carbonation indicator and petrographic observations were also reported as favourable. · Field measurements indicated temperature-gradient differences of about 1.0–1.2°C and an upward-curling difference of about 0.05 mm between BFS-FA and sand panels, with no reported difference in downward curling. · The findings support the potential use of suitably processed and source-characterized BFS as a full fine-aggregate replacement in pavement quality concrete. The results should not be generalized to other BFS sources without characterization and mix validation.
[1] U. S. Department of Transportation, Federal Highway Administration, “Use of Air-Cooled Blast Furnace Slag as Coarse Aggregate in Concrete Pavements,” Report No. FHWA-HIF-12-008, Mar. 2012. [2] D. M. Hammerling, “Calcium Sulfide as Blast Furnace Slag Used as Concrete Aggregate,” M.S. thesis, Michigan Technological University, Houghton, MI, 1999. [3] D. W. Lewis, “Properties and Uses of Iron and Steel Slags,” National Slag Association, 1982. [4] K. T. Manoj, B. Samir, and K. D. Umesh, “Steel slag utilization—Overview in Indian perspective,” Int. J. Adv. Res., vol. 4, no. 8, pp. 2232–2246, 2016. [5] I. Jain, Concrete Technology. Tech-Max Publications. [6] Bureau of Indian Standards, IS 10262:2009, Concrete Mix Proportioning—Guidelines, New Delhi, India, 2009. [7] J. J. Emery, “Palletized lightweight slag aggregate,” in Proc. Concrete International, Concrete Society, 1980. [8] A. S. Noureldin and R. S. McDaniel, “Evaluation of surface mixtures of steel slag and asphalt,” Transportation Research Record 1269, Transportation Research Board, Washington, DC, pp. 133–149, 1990. [9] S. R. Rao, Resource Recovery and Recycling from Metallurgical Wastes, Waste Management Series 7. Amsterdam, The Netherlands: Elsevier, 2006, pp. 269–327. [10] I. M. Asi, “Evaluating skid resistance of different asphalt concrete mixes,” Building and Environment, vol. 42, no. 1, pp. 325–329, 2007.
Publication Date
11/13/2026
Peer Review Type
Double-Blind Peer Review
Review Rounds: 2
Documents
Article Views
0
Total views since publication
PDF Downloads
2
Total downloads since publication
Geographic Reach
5
Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.
Plagiarism Screening
This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.
Conflict of Interest
The authors declare no conflict of interest related to this research work.
Funding Information
No funding information available for this research.
Related research in the same subject area
Loading similar articles...