Loading article...
Loading article...
Stream/Area:
-
Subject:
-
Paper ID:
IJSREM68985
Volume:
10 |
11 |
Nov 2026
Pages:
1-4
Publication Frequency:
Monthly (12 issues per year)
License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.
Department of electronics engineering
MS.Bidve Engineering College Latur
Department of electronics engineering
MS.Bidve Engineering College Latur
Department of electronics engineering
MS.Bidve Engineering College Latur
Overspeeding is a leading cause of road accidents, yet commercial speed-enforcement equipment such as radar guns and speed cameras is costly and opaque for educational use. This paper presents the design and implementation of a low-cost vehicle speed detection and overspeed alert system built around an AT89C51 (8051) microcontroller and two infrared (IR) sensor modules placed 12 cm apart. When a vehicle is detected by the first sensor, Timer0 is started; when it reaches the second sensor, the timer is stopped and the elapsed count is converted to speed using the distance–time relation. The result is shown on a 16×2 LCD, and a transistor-driven buzzer raises an audible alarm whenever the measured speed exceeds a programmed limit. An 11.0592 MHz crystal gives a machine-cycle time of 1.085 µs, so timer resolution is not the limiting factor of the design. The paper describes the architecture, circuit connections, timing analysis and control algorithm, and estimates a bill of materials of about ₹1,830. The prototype shows that automatic speed measurement and overspeed indication can be achieved with inexpensive, widely available components, which makes it well suited to embedded-systems teaching and small-scale road-safety demonstrations.
KEYWORDS
A low-cost vehicle speed detection and overspeed alert system based on the AT89C51 microcontroller and two IR sensors has been designed and implemented. The system measures the travel time between two sensors 12 cm apart with Timer0, computes the speed from the distance–time relation, displays it on a 16×2 LCD and triggers a buzzer through a transistor driver when the programmed limit is exceeded. The analysis shows a timing resolution of 1.085 µs and a minimum measurable speed of about 6.1 km/h in 16-bit mode, and the estimated cost is about ₹1,830. The design is simple, economical and extensible, and offers a practical platform for embedded-systems education and road-safety demonstration.
[1] Nafiza, “Speed detection of vehicles using IR sensors,” Current Trends in Signal Processing, vol. 12, no. 1, May 2022. [2] V. Q. Vu, L. N. Van, V. T. Thang, and V. P. Doan, “Vehicle speed estimation using two roadside passive infrared sensors,” Int. J. Mod. Phys. B, 2020, doi: 10.1142/S0217979220401517. [3] M. A. Mazidi, J. G. Mazidi, and R. D. McKinlay, The 8051 Microcontroller and Embedded Systems: Using Assembly and C, 2nd ed. Pearson Education, 2006. [4] K. J. Ayala, The 8051 Microcontroller, 3rd ed. Cengage Learning, 2005. [5] Microchip Technology, “AT89C51 datasheet.” [6] Keil Software, “C51 compiler documentation.”
Publication Date
11/14/2026
Peer Review Type
Double-Blind Peer Review
Review Rounds: 2
Documents
Article Views
0
Total views since publication
PDF Downloads
2
Total downloads since publication
Geographic Reach
5
Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.
Plagiarism Screening
This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.
Conflict of Interest
The authors declare no conflict of interest related to this research work.
Funding Information
No funding information available for this research.
Related research in the same subject area
Loading similar articles...