Loading article...
Loading article...
Stream/Area:
-
Subject:
-
Paper ID:
IJSREM68742
Volume:
10 |
11 |
Nov 2026
Pages:
1-7
Publication Frequency:
Monthly (12 issues per year)
License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.
VLSI DESIGN
DR. SIVANTHI ADITANAR COLLEGE OF ENGINEERING
The Advanced Peripheral Bus (APB) of the AMBA specification is widely used to connect low-bandwidth peripherals in System-on-Chip (SoC) designs, where power consumption has become a critical constraint. This paper presents the design and synthesis of a low-power AMBA APB bus protocol using a combination of Finite State Machine (FSM) optimization, operand isolation, and clock gating. The FSM is optimized through efficient state encoding to reduce switching activity and combinational logic complexity. Operand isolation prevents unnecessary toggling in data path blocks when they are idle, while clock gating disables the clock to inactive registers, lowering dynamic power dissipation. The design is described in Verilog HDL, functionally verified through simulation, and synthesized to evaluate area, timing, and power. Results show a notable reduction in dynamic power compared with the conventional APB implementation, with no loss of protocol functionality or timing compliance. The proposed approach is well suited to energy efficient SoC and IoT applications.
KEYWORDS
The low-power AMBA APB protocol was designed in Verilog and verified in Vivado, with all five configurations (BASE, FSM, ISO, CG, ALL) producing identical, correct read and write behaviour. FSM optimization reduced the master from seven binary-encoded states to three Gray-coded states, lowering logic and state-transition switching. Operand isolation and clock gating cut unnecessary toggling on the bus and idle blocks, reducing dynamic power compared with the baseline, with the largest savings when the bus is mostly idle. The combined configuration (ALL) gave the best power result, and the savings are reported from SAIF-based activity, so they reflect real switching behaviour (insert your measured percentages here). Future scope includes adding PSLVERR error handling, extending the design to more slaves and an AHB-to-APB bridge, evaluating it in an ASIC flow with latch-based clock gating, and adding assertion-based verification.
[1] AMD (Xilinx), “Vivado Design Suite User Guide: Power Analysis and Optimization,” UG907, [2] ARM Ltd., “AMBA APB Protocol Specification, Version 2.0,” ARM IHI 0024C, 2010. [3] Dwivedi, N. Mishra, and A. Singh-Rajput, “Assertion & Functional Coverage Driven Verification of AMBA Advance Peripheral Bus Protocol Using System Verilog,” 2021 International Conference on Advances in Electrical, Computing, Communication and Sustainable Technologies (ICAECT), February 2021, DOI: 10.1109/ICAECT49130.2021.9392518. [4] Gupta, K. Rawat, S. Pandey, P. Kumar, S. Kumar, and H. P. Singh, “Physical design implementation of 32-bit AMBA ASB APB module with improved performance,” 2016 International Conference on Electrical, Electronics, and Optimization Techniques (ICEEOT), 2016, pp. 3121–3124, DOI: 10.1109/ICEEOT.2016.7755276. [5] Jain and S. Rao, “Design and Verification of Advanced Microcontroller Bus Architecture-Advanced Peripheral Bus (AMBA-APB) Protocol,” 2021 Third International Conference on Intelligent Communication Technologies and Virtual Mobile Networks (ICICV), February 2021, DOI: 10.1109/ICICV50876.2021.9388549. [6] Ma, Z. Liu, and X. Ma, “Design and implementation of APB bridge based on AMBA 4.0,” 2011 International Conference on Consumer Electronics, Communications and Networks (CECNet), 2011, pp. 193–196, DOI: 10.1109/CECNET.2011.5768692. [7] Manu and P. Prabhavathi, “Design and implementation of AMBA ASB APB bridge,” 2013 International Conference on Fuzzy Theory and Its Applications (iFUZZY), 2013, pp. 234–238, DOI: 10.1109/iFuzzy.2013.6825442. [8] Münch, N. Wehn, B. Wurth, R. Mehra, and J. Sproch, “Automating RT-level operand isolation to minimize power consumption in datapaths,” Proc. Design, Automation and Test in Europe Conference (DATE), March 2000, pp. 624–631. [9] Ravikumar, K. B. Ganesha, C. Y. Chethana, and T. M. Parikshith Roy, “Design and Verification of Advanced Microcontroller Bus Architecture (AMBA) Advanced Peripheral Bus (APB) Protocol,” 2024 International Conference on Smart Systems for Applications in Electrical Sciences (ICSSES), May 2024, DOI: 10.1109/ICSSES62373.2024.10561369. [10] Rawat, K. Sahni, and S. Pandey, “RTL implementation for AMBA ASB APB protocol at system on chip level,” 2015 2nd International Conference on Signal Processing and Integrated Networks (SPIN), 2015, pp. 927–930, DOI: 10.1109/SPIN.2015.7095347.
Publication Date
11/5/2026
Peer Review Type
Double-Blind Peer Review
Review Rounds: 2
Documents
Article Views
0
Total views since publication
PDF Downloads
7
Total downloads since publication
Geographic Reach
5
Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.
Plagiarism Screening
This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.
Conflict of Interest
The authors declare no conflict of interest related to this research work.
Funding Information
No funding information available for this research.
Related research in the same subject area
Loading similar articles...