Crossref DOIMemberCiteFactoropen accessissn
SJIF Impact Factor 8.659 | ISSN: 2582-3930
IJSREM Logo

International Journal of Scientific Research in Engineering and Management

(Gateway to Global Scholars - An International, Scholarly, Multi-Disciplinary, Open Access Journal)

Peer-Reviewed Journal Designed to Meet UGC's Quality Parameters

HomeCurrent IssuePast IssuesPay OnlineConferencesEditorial BoardAbout UsContact Us
IJSREM

Follow Us

  • Google Scholar
  • ResearchGate
  • Academia.edu
  • Mendeley
  • LinkedIn
  • Facebook
  • Instagram

Journal Policies

  • Peer Review Policy
  • Publication Ethics
  • Copyright Infringement
  • Refund & Cancellation Policy
  • Terms and Conditions
  • Privacy Policy

Journal Identifiers & Licenses

  • ISSN Verified: 2582-3930ISSN Verified: 2582-3930
  • Crossref DOI: 10.55041Crossref DOI: 10.55041
  • SJIF Ranking: 08.659SJIF Ranking: 08.659
  • Licensed under CC BY 4.0Licensed under CC BY 4.0
  • ISO Certification: 9001:2015ISO Certification: 9001:2015
  • Indexed & Cited In: Google ScholarIndexed & Cited In: Google Scholar

Contact Us

International Journal of Scientific Research in Engineering and Management (IJSREM)

#62/1, New No 7, 1st Cross, 2nd Main, Ganganagar, R T Nagar, Bangalore North, Bangalore, Karnataka, India – 560032
[email protected]+91 93911 67991
logos
logos
Working Hours

Mon – Sat: 9:00 AM – 6:00 PM

Sunday: 10:00 AM – 4:00 PM

+91 93911 67991

© 2026 IJSREM – International Journal of Scientific Research in Engineering and Management. This is an open-access journal. Articles are published under the Creative Commons Attribution (CC BY 4.0) License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

DisclaimerPrivacy PolicyTerms and Conditions
ArticlePeer ReviewedOpen AccessPlagiarism Passed
Paper ID:IJSREM65794

Eco - Friendly And Cost - Effective Self Compacting Concrete Using Foundry Sand

Stream/Area:

-

Subject:

-

Paper ID:

IJSREM65794

Volume:

10 |

7 |

Jul 2026

Pages:

1-9

Publication Frequency:

Monthly (12 issues per year)

DOI
Digital Object Identifier
10.55041/IJSREM65794

License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.

Share this article:

Authors

Durga Priyadharshini M

Durga Priyadharshini M

Department of civil engineering

Karpagam academy of higher education

Download Author Certificate

Mentors

Dr.V.Johnpaul

Dr.V.Johnpaul

Department of civil engineering

Karpagam academy of higher education

Download Mentor Certificate

Author Services & Downloads

Full ArticlesAcceptance Certificate

Abstract

The way waste foundry sand is disposed of in industry presents serious environmental problems. particularly in the foundry sector, To address this issue, an experimental investigation was conducted and evaluate the effects on Using leftover foundry sand in concrete to partially substitute natural sand, specifically targeting M30 grade concrete, which design is to achieve compressive strength of 30 MPa in 28 days. In the study, percentage (0%,25%,50%,100%) of the foundry sand was replaced with fine aggregate. The performance in both conventional concrete and concrete with WFS was assessed through various tests, including compressive strength, using the weight loss method in cement mortar (CM).The results revealed a slight improvement in strength and durability. Notably, the benefits were more pronounced in MM 10 grade cement mortar. This research highlights the potential of utilizing industrial by-products like WFS in construction, contributing to waste reduction and promoting sustainable practices in the concrete industry.

KEYWORDS

Compression test Mortar Foundry sand Strength and durability Waste management.

Cite This Article

Full Article/Conclusion

l  The present study examined the physical and chemical characteristics of waste foundry sand (WFS). The compressive strength of concrete was evaluated using both untreated and reclaimed WFS as partial replacements for natural sand at proportions of 25%, 50%, 75%, and 100%. Based on the experimental findings, the following conclusions were drawn. l  From the tests conducted on the six concrete mixtures, it was observed that at all curing ages, the strength of concrete containing up to 25% WFS and reclaimed WFS was nearly comparable to that of the conventional mix (CM). However, mixtures with 25% to 50% replacement levels showed a slight reduction in compressive strength. At 28 days, the decrease was approximately 1.6% and 5.7%, respectively, compared to the conventional mix. l  It shows the 25% and 50% of Partial replacement of foundry sand concrete is best one compare to cc. l  The results indicate that waste foundry sand (WFS) and reclaimed WFS can be effectively used as partial replacements for fine aggregate up to 25% and 50%. At these replacement levels, good quality concrete can be produced without compromising the required standards.

References

  [1]                   IS 10262–2009: Indian Standard “Guidelines for concrete mix design proportioning” – code of practice. [2]                   IS 456 – 2000: Indian Standard “Plain and reinforced concrete” – code of practice. [3]                   IS 383 – 1970 : Indian Standard “Specification for coarse and fine aggregates from naturals sources for concrete” [4]                   IS: 2386(Part I)-1963. “methods of test for aggregates for concrete” [5]                   J. Jeyanthi et.al (2023), “Study of concrete with partial replacement of waste foundry sand for fine aggregate and granite waste for coarse aggregate” [6]                   Wenzhong Zheng et.al (2023), “Preparation of ultra-high performance concrete containing waste foundry sand and its application in structures” [7]                   M.Arun et.al(2021), “Cost effective construction materials for economically weaker section” [8]                   V. Brindha Devi et.al. (2023), “Experimental investigation on utilization of used foundry sand in concrete as fine aggregate” [9]                   P.PendhariAnush et.al. (2017), “Partial replacement of sand by waste foundry sand”. Journal of Civil Engineering Research ( JCER ). [10]               Saifali et.al. (2017), “A Review of Utilization of Waste foundry sand” Journal of Civil Engineering Research ( JCER ).

Editorial & Review Transparency

Publication Date

7/3/2026

Peer Review Type

Double-Blind Peer Review

Review Rounds: 2

Documents

Review Report (Confidential)
Copyright Form (Office)

Article Metrics & Impact

Article Views

0

Total views since publication

PDF Downloads

0

Total downloads since publication

Geographic Reach

5

Indexing, Archiving & Preservation

Google Scholar
Academia
ResearchGate
Crossref
SSRN
Semantic Scholar
Thomson Reuters
WorldCat
Mendeley
OpenAlex
EBSCO
Zenodo

Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.

Ethics, Compliance & Transparency

Plagiarism Screening

This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.

Conflict of Interest

The authors declare no conflict of interest related to this research work.

Funding Information

No funding information available for this research.

Similar & Recommended Articles

Similar Articles by Topic

Related research in the same subject area

Loading similar articles...