Crossref DOIMemberCiteFactoropen accessissn
SJIF Impact Factor 8.659 | ISSN: 2582-3930
IJSREM Logo

International Journal of Scientific Research in Engineering and Management

(Gateway to Global Scholars - An International, Scholarly, Multi-Disciplinary, Open Access Journal)

Peer-Reviewed Journal Designed to Meet UGC's Quality Parameters

HomeCurrent IssuePast IssuesPay OnlineConferencesEditorial BoardAbout UsContact Us
IJSREM

Loading article...

Follow Us

  • Google Scholar
  • ResearchGate
  • Academia.edu
  • Mendeley
  • LinkedIn
  • Facebook
  • Instagram

Journal Policies

  • Peer Review Policy
  • Publication Ethics
  • Copyright Infringement
  • Refund & Cancellation Policy
  • Terms and Conditions
  • Privacy Policy

Journal Identifiers & Licenses

  • ISSN Verified: 2582-3930ISSN Verified: 2582-3930
  • Crossref DOI: 10.55041Crossref DOI: 10.55041
  • SJIF Ranking: 08.659SJIF Ranking: 08.659
  • Licensed under CC BY 4.0Licensed under CC BY 4.0
  • ISO Certification: 9001:2015ISO Certification: 9001:2015
  • Indexed & Cited In: Google ScholarIndexed & Cited In: Google Scholar

Contact Us

International Journal of Scientific Research in Engineering and Management (IJSREM)

#62/1, New No 7, 1st Cross, 2nd Main, Ganganagar, R T Nagar, Bangalore North, Bangalore, Karnataka, India – 560032
[email protected]+91 93911 67991
logos
logos
Working Hours

Mon – Sat: 9:00 AM – 6:00 PM

Sunday: 10:00 AM – 4:00 PM

+91 93911 67991

© 2026 IJSREM – International Journal of Scientific Research in Engineering and Management. This is an open-access journal. Articles are published under the Creative Commons Attribution (CC BY 4.0) License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited.

DisclaimerPrivacy PolicyTerms and Conditions
ArticlePeer ReviewedOpen AccessPlagiarism Passed
Paper ID:IJSREM68879

Planning, Analysis and Design of G+2 Residential Building Using STAAD.Pro (V8i)

Stream/Area:

-

Subject:

-

Paper ID:

IJSREM68879

Volume:

10 |

11 |

Nov 2026

Pages:

1-10

Publication Frequency:

Monthly (12 issues per year)

DOI
Digital Object Identifier
10.55041/IJSREM68879

License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.

Share this article:

Authors

IG

Iyapan G

Department of Civil Engineering

Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli

Download Author Certificate
JSS

Jai Suriya S

Department of Civil Engineering

Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli

Download Co-Author Certificate
VRS

Varun Ritvik S

Department of Civil Engineering

Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli

Download Co-Author Certificate
YKN

Yuga Kavithanjan N

Department of Civil Engineering

Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli

Download Co-Author Certificate

Author Services & Downloads

Full ArticlesAcceptance Certificate

Abstract

This study presents a preliminary structural design of a ground-plus-two-storey reinforced concrete residential building by combining three-dimensional modelling in STAAD.Pro V8i with manual limit-state design. One-way and two-way slabs, a T-beam, columns under uniaxial and biaxial bending, an isolated footing, and a dog-legged staircase were assessed under factored gravity loads using IS 456:2000. The member calculations adopted M25 concrete and reinforcement with a nominal yield strength of 500 MPa. Minimum reinforcement governed the one-way slab, for which 201 mm²/m was provided against a minimum of 150 mm²/m. The two-way slab had a calculated shear stress of 0.14 MPa and a span-to-effective-depth ratio of 27.9, compared with the reported limits of 0.37 MPa and 32, respectively. The representative beam had a calculated factored bending moment of 123.9 kN·m and a shear force of 117.2 kN. For the 1.50 m square isolated footing, the service bearing pressure due to the column load alone was 186.7 kPa against an assumed allowable bearing pressure of 200 kPa. The results document the preliminary gravity-load design of selected members. Building-level assessment requires verification of the biaxial column interaction, reconciliation of the footing depth and shear calculations, and evaluation of the seismic response of the three-dimensional model

KEYWORDS

Reinforced cement concrete G+2 residential building STAAD.Pro V8i structural analysis slab design column design isolated footing

Cite This Article

Iyapan G, Jai Suriya S, Varun Ritvik S, Yuga Kavithanjan N, "Planning, Analysis and Design of G+2 Residential Building Using STAAD.Pro (V8i)," International Journal of Scientific Research in Engineering and Management, vol. 10, no. 11, pp. 1-10, Nov 2026. https://doi.org/10.55041/IJSREM68879

Full Article/Conclusion

This study combined three-dimensional modelling in STAAD.Pro V8i with manual limit-state calculations to document the preliminary gravity-load design of a ground-plus-two-storey reinforced concrete residential building. The calculations identified the governing criteria for selected members and quantified the difference between required and provided reinforcement.   Minimum reinforcement governed the one-way slab, for which 201 mm²/m was provided against a minimum requirement of 150 mm²/m. The two-way slab developed a calculated shear stress of 0.14 MPa against a reported resistance of 0.37 MPa. Its span-to-effective-depth ratio was 27.9, below the adopted limit of 32. For the 1.50 m square isolated footing, the calculated service bearing pressure was 186.7 kPa against an assumed allowable pressure of 200 kPa. This estimate accounts for the column load alone. The footing reinforcement provided approximately 377 mm²/m in each direction against the reported requirement of 332 mm²/m.   These findings apply to the selected members under the adopted gravity-load assumptions. The biaxial column interaction requires verification of the limiting moments about both axes. The footing assessment requires a consistent effective depth for the flexural, one-way shear, and punching shear checks, together with site-specific confirmation of the allowable bearing pressure. Although seismic loading was defined in the model, the reported results establish only the preliminary gravity-load design basis. A building-level assessment requires documented lateral response, governing load combinations, and verification of ductile detailing.

References

[1] Bureau of Indian Standards, Plain and Reinforced Concrete—Code of Practice, 4th rev., IS 456:2000. New Delhi, India, 2000. standards.bis.gov.in [2] Bureau of Indian Standards, Code of Practice for Design Loads (Other Than Earthquake) for Buildings and Structures—Part 1: Dead Loads—Unit Weights of Building Materials and Stored Materials, 2nd rev., IS 875 (Part 1):1987. New Delhi, India, 1987. 1987 Indian St [3] Bureau of Indian Standards, Code of Practice for Design Loads (Other Than Earthquake) for Buildings and Structures—Part 2: Imposed Loads, 2nd rev., IS 875 (Part 2):1987. New Delhi, India, 1987. bis.gov.in [4] Bureau of Indian Standards, Criteria for Earthquake Resistant Design of Structures—Part 1: General Provisions and Buildings, 6th rev., IS 1893 (Part 1):2016. New Delhi, India, 2016. bis.gov.in [5] Bureau of Indian Standards, Design Aids for Reinforced Concrete to IS 456:1978, SP 16:1980. New Delhi, India, 1980. bnec.ac.in [6] Bureau of Indian Standards, Ductile Design and Detailing of Reinforced Concrete Structures Subjected to Seismic Forces—Code of Practice, 1st rev., IS 13920:2016. New Delhi, India, 2016. BIS [7] Bureau of Indian Standards, Code of Practice for Design Loads (Other Than Earthquake) for Buildings and Structures—Part 5: Special Loads and Load Combinations, 2nd rev., IS 875 (Part 5):1987. New Delhi, India, 1987. services.bis.gov.in [8] Bentley Systems, STAAD.Pro V8i [structural analysis and design software]. Communities [9] G. T. Naidu, K. Devi, V. Dunesh, D. B. Prasad, M. C. Naga Sai, and V. G. Yedla, “Planning, designing and estimation of G+2 residential building using AutoCAD and STAAD PRO,” International Journal for Research in Applied Science & Engineering Technology, vol. 12, no. 4, pp. 205–207, 2024. DOI. www.ijraset.com [10] M. M. Mabula, M. Taki, J. Mize, D. Dutta, M. Deka, J. Doni, and N. Goswami, “Comparison between manual and software approach towards analysis and design of a residential building,” International Journal for Research in Applied Science & Engineering Technology, vol. 11, no. 6, pp. 4488–4499, 2023. DOI. ijraset.com

Editorial & Review Transparency

Publication Date

11/11/2026

Peer Review Type

Double-Blind Peer Review

Review Rounds: 2

Documents

Review Report (Confidential)
Copyright Form (Office)

Article Metrics & Impact

Article Views

1

Total views since publication

PDF Downloads

6

Total downloads since publication

Geographic Reach

5

Indexing, Archiving & Preservation

Google Scholar
Academia
ResearchGate
Crossref
SSRN
Semantic Scholar
Thomson Reuters
WorldCat
Mendeley
OpenAlex
EBSCO
Zenodo

Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.

Ethics, Compliance & Transparency

Plagiarism Screening

This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.

Conflict of Interest

The authors declare no conflict of interest related to this research work.

Funding Information

No funding information available for this research.

Similar & Recommended Articles

Similar Articles by Topic

Related research in the same subject area

Loading similar articles...