Loading article...
Loading article...
Stream/Area:
-
Subject:
-
Paper ID:
IJSREM69089
Volume:
10 |
11 |
Nov 2026
Pages:
1-10
Publication Frequency:
Monthly (12 issues per year)
License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.
Department of Civil Engineering
Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli
Department of Civil Engineering
Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli
Department of Civil Engineering
Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli
Department of Civil Engineering
Kongunadu College of Engineering and Technology (Autonomous), Tiruchirappalli
The increasing demand for multifunctional infrastructure necessitates the development of structurally efficient, safe, and sustainable building systems that integrate architectural functionality with reliable engineering design. This study presents an integrated approach to the planning, three-dimensional structural analysis, and design of a ground-plus-two-storey (G+2) reinforced concrete (RC) multi-purpose building using AutoCAD and STAAD.Pro V8i. Architectural planning was undertaken considering spatial efficiency, accessibility, functional requirements, and structural continuity. A three-dimensional analytical model was developed by incorporating structural geometry, material properties, member characteristics, support conditions, and relevant loading parameters. M25-grade concrete and Fe500D reinforcement steel were adopted, while gravity and seismic loading provisions were considered with reference to applicable Indian Standards, including IS 456:2000, IS 875, and IS 1893 (Part 1):2016. Structural responses were evaluated in terms of axial forces, bending moments, shear forces, support reactions, and deflections. The design methodology incorporated limit-state principles and member-level calculations for slabs, beams, columns, isolated footings, and staircases. The illustrative design results included a 230 × 500 mm reinforced concrete beam subjected to a factored bending moment of 123.91 kN·m and a factored shear force of 117.17 kN, together with a 400 × 450 mm column subjected to a factored axial load of 630 kN. The study establishes a systematic framework for integrating computer-aided structural analysis with conventional reinforced concrete design procedures. However, comprehensive verification of seismic response, structural detailing, and foundation performance remains necessary before practical implementation. The proposed methodology provides a basis for the preliminary structural assessment and design development of multi-purpose reinforced concrete buildings.
KEYWORDS
The present study investigated the integrated planning, structural analysis, and preliminary design of a ground-plus-two-storey (G+2) reinforced concrete multi-purpose building using AutoCAD and STAAD.Pro V8i. The investigation demonstrated the application of three-dimensional numerical modelling and limit state design principles to evaluate structural behaviour under prescribed loading conditions. Based on the analytical procedures and reported design calculations, the following conclusions were drawn. The integration of architectural planning and structural modelling provided a systematic framework for developing the G+2 reinforced concrete building. The adopted structural configuration incorporated slabs, beams, columns, isolated footings, and staircases to establish the intended gravity-load transfer mechanism. The three-dimensional structural model developed using STAAD.Pro V8i facilitated the evaluation of structural responses, including bending moments, shear forces, axial forces, support reactions, and deflections. These parameters formed the basis for identifying structural demands and determining preliminary member dimensions and reinforcement requirements. The reinforced concrete beam with a cross-sectional dimension of 230 × 500 mm was designed for a factored bending moment of 123.91 kN·m and a corresponding shear force of 117.17 kN. The reported design adopted longitudinal reinforcement and transverse stirrups based on the calculated flexural and shear demands. The reinforced concrete columns, with adopted cross-sectional dimensions of 400 × 450 mm, were evaluated under axial compression and uniaxial or biaxial bending conditions. The reported factored axial load of 630 kN and associated bending moments were used to determine the required reinforcement and assess the interaction between axial and flexural resistance. The slab design calculations considered one-way and two-way bending behaviour, with adopted thicknesses of 125 mm and 150 mm, respectively. The reported calculations included flexural reinforcement, shear resistance, and deflection-control checks in accordance with the adopted limit state design approach. The isolated footing design adopted a plan dimension of 1.50 × 1.50 m based on an assumed safe bearing capacity of 200 kN/m². The reported calculations provided a preliminary assessment of soil pressure, bending resistance, and reinforcement requirements. However, the adequacy of the foundation remains subject to verification of punching shear, one-way shear, actual geotechnical conditions, and reinforcement detailing. The combined application of computer-aided structural analysis and conventional design calculations established a practical workflow for preliminary structural design. Nevertheless, comprehensive verification of seismic response, load combinations, structural detailing, and foundation
1. Bathe, K. J. (1996). Finite element procedures. Prentice Hall. 2. Bentley Systems. (n.d.). STAAD.Pro CONNECT Edition: User documentation and technical reference. 3. Bureau of Indian Standards. (1980). Design aids for reinforced concrete to IS 456:1978 (SP 16:1980). 4. Bureau of Indian Standards. (1987a). Code of practice for design loads (other than earthquake) for buildings and structures: Dead loads (IS 875, Part 1:1987). 5. Bureau of Indian Standards. (1987b). Code of practice for design loads (other than earthquake) for buildings and structures: Imposed loads (IS 875, Part 2:1987). 6. Bureau of Indian Standards. (1987c). Handbook on concrete reinforcement and detailing (SP 34:1987). 7. Bureau of Indian Standards. (2000). Plain and reinforced concrete—Code of practice (IS 456:2000). 8. Bureau of Indian Standards. (2015). Design loads (other than earthquake) for buildings and structures: Wind loads (IS 875, Part 3:2015). 9. Bureau of Indian Standards. (2016a). National Building Code of India 2016 (SP 7:2016). 10. Bureau of Indian Standards. (2016b). Criteria for earthquake resistant design of structures: General provisions and buildings (IS 1893, Part 1:2016).
Publication Date
11/17/2026
Peer Review Type
Double-Blind Peer Review
Review Rounds: 2
Documents
Article Views
0
Total views since publication
PDF Downloads
3
Total downloads since publication
Geographic Reach
5
Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.
Plagiarism Screening
This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.
Conflict of Interest
The authors declare no conflict of interest related to this research work.
Funding Information
No funding information available for this research.
Related research in the same subject area
Loading similar articles...