Loading article...
Loading article...
Stream/Area:
-
Subject:
-
Paper ID:
IJSREM68948
Volume:
10 |
11 |
Nov 2026
Pages:
1-7
Publication Frequency:
Monthly (12 issues per year)
License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.
Department of Civil Engineering
Sanketika Vidya Parishad Engineering College, P.M. Palem, Visakhapatnam – 530041, Andhra Pradesh, India
Department of Civil Engineering
Sanketika Vidya Parishad Engineering College, P.M. Palem, Visakhapatnam – 530041, Andhra Pradesh, India
This study evaluates the influence of seismic-zone classification on the response of a regular G+10 reinforced concrete (RC) framed building using the response spectrum method in STAAD.Pro. The building has a 24 m × 24 m plan comprising four 6 m bays in each principal direction and a total height of 33.6 m. The adopted member dimensions are 300 × 500 mm for beams and 500 × 500 mm for columns, with 125 mm slabs. M30 concrete and Fe500 reinforcement are specified. The comparison considers Seismic Zones II, III and V while maintaining the same geometry, material properties, gravity-loading assumptions, soil category, damping and support conditions. The manually estimated seismic weight is 75,865 kN. Based on the stated design horizontal seismic coefficients, the estimated base shears are 986, 1,577 and 3,549 kN for Zones II, III and V, respectively. Provisional estimates of roof displacement (45, 72 and 162 mm), maximum inter-storey drift (9.0, 14.4 and 32.4 mm) and critical beam moment (131, 168 and 246 kN·m) are also examined. These displacement, drift and member-force values are preliminary estimates and are not validated direct extractions from STAAD.Pro response-spectrum analysis. In addition, the reported horizontal support reaction of approximately 17.922 kN is inconsistent with the manual Zone II base-shear estimate. The findings are therefore interpreted as preliminary comparative estimates, and the model checks required for validation are identified.
KEYWORDS
1. A regular G+10 RC frame with a 24 m × 24 m plan and a total height of 33.6 m was considered for a comparative seismic investigation using the response spectrum method. 2. Using the adopted zone factors and the estimated seismic weight of 75,865 kN, the manual base-shear estimates are approximately 986 kN, 1,577 kN and 3,549 kN for Zones II, III and V, respectively. 3. The estimated manual base shear increases by approximately 60% between Zones II and III and by approximately 260% between Zones II and V. 4. The provisional response estimates indicate increasing roof displacement, inter-storey drift and member-force demand as the adopted seismic zone becomes more severe. These trends require confirmation through validated response-spectrum analysis. 5. The preliminary reinforcement provisions increase with seismic-zone severity. Their adequacy cannot be established without complete member-design checks and ductile-detailing verification in accordance with the applicable Indian Standards. 6. The reported horizontal support reaction of approximately 17.922 kN is inconsistent with the manual Zone II base-shear estimate. The available STAAD.Pro output therefore does not establish a validated response-spectrum result. 7. With unchanged structural mass and stiffness, the fundamental period is expected to remain broadly similar across the zone cases. The value of approximately 1.05 s is an empirical estimate and must be replaced by the verified modal period from the analytical model. 8. Among the three zones considered, Zone V produces the highest manual base-shear estimate and the highest provisional response estimates.
[1] Bureau of Indian Standards, IS 1893 (Part 1):2016, Criteria for Earthquake Resistant Design of Structures—General Provisions and Buildings. New Delhi, India: BIS, 2016. [2] Bureau of Indian Standards, IS 13920:2016, Ductile Design and Detailing of Reinforced Concrete Structures Subjected to Seismic Forces. New Delhi, India: BIS, 2016. [3] Bureau of Indian Standards, IS 456:2000, Plain and Reinforced Concrete—Code of Practice. New Delhi, India: BIS, 2000. [4] Bureau of Indian Standards, IS 875 (Part 2):1987, Code of Practice for Design Loads (Other than Earthquake) for Buildings and Structures—Imposed Loads. New Delhi, India: BIS, 1987. [5] Bentley Systems, STAAD.Pro CONNECT Edition—Technical Reference Manual. Exton, PA, USA: Bentley Systems. [6] A. K. Chopra, Dynamics of Structures: Theory and Applications to Earthquake Engineering, 5th ed. Hoboken, NJ, USA: Pearson, 2017. [7] S. K. Duggal, Earthquake Resistant Design of Structures, 2nd ed. New Delhi, India: Oxford University Press, 2013. [8] P. Agarwal and M. Shrikhande, Earthquake Resistant Design of Structures. New Delhi, India: PHI Learning, 2006. [9] T. Paulay and M. J. N. Priestley, Seismic Design of Reinforced Concrete and Masonry Buildings. New York, NY, USA: Wiley, 1992. [10] E. L. Wilson, A. Der Kiureghian and E. P. Bayo, “A replacement for the SRSS method in seismic analysis,” Earthquake Engineering and Structural Dynamics, vol. 9, no. 2, pp. 187–194, 1981, doi: 10.1002/eqe.4290090207.
Publication Date
11/13/2026
Peer Review Type
Double-Blind Peer Review
Review Rounds: 2
Documents
Article Views
0
Total views since publication
PDF Downloads
2
Total downloads since publication
Geographic Reach
5
Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.
Plagiarism Screening
This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.
Conflict of Interest
The authors declare no conflict of interest related to this research work.
Funding Information
No funding information available for this research.
Related research in the same subject area
Loading similar articles...