Loading article...
Loading article...
Stream/Area:
-
Subject:
-
Paper ID:
IJSREM68939
Volume:
10 |
11 |
Nov 2026
Pages:
1-8
Publication Frequency:
Monthly (12 issues per year)
License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.
Department of Civil Engineering
Sanketika Vidya Parishad Engineering College, P.M. Palem, Visakhapatnam – 530041, Andhra Pradesh, India
Department of Civil Engineering
Sanketika Vidya Parishad Engineering College, P.M. Palem, Visakhapatnam – 530041, Andhra Pradesh, India
The present study investigates the use of waste-polymer-coated aggregates in bituminous pavement construction through laboratory characterization of aggregates and Marshall evaluation of a dense bituminous mixture prepared with VG-30 bitumen. The experimental programme described in the project report includes comparison of conventional and coated aggregates using mechanical and physical tests, together with Marshall stability, flow and volumetric measurements. The report records an abrasion-test series for coating proportions of 0%, 5%, 5.5%, 6% and 8%, in which the Los Angeles abrasion value decreases from 18.80% for the uncoated aggregate to 8.80%, 9.20%, 10.60% and 7.60%, respectively. A separate results discussion describes coating levels of 0.5%, 1% and 2% for aggregates from different sources and reports reductions in abrasion, crushing and water-absorption values. The Marshall trial data at 8.0%, 8.5% and 9.0% bitumen contents show stability values of 2580, 2627 and 2410 kg, respectively, with the maximum recorded value at 8.5% binder content. However, the project report states that the final polymer-coated dense bituminous mix did not satisfy the cited IRC requirements. The findings therefore indicate potential improvements in selected aggregate properties, but do not establish compliance or field durability of the complete mix. Inconsistencies in the reported polymer dosage series and incomplete optimum-bitumen-content calculations are identified as limitations requiring verification.
KEYWORDS
The following conclusions are drawn strictly from the experimental information documented in the project report: 1. Polymer coating was successfully applied to aggregate surfaces using the dry process described in the project. 2. The reported abrasion-test series (0–8% coating) shows lower Los Angeles abrasion values for coated aggregates than for the uncoated sample; the lowest reported value is 7.60% at 8% coating. 3. The separate source-specific results in the report describe reductions in abrasion, crushing, impact and water-absorption values at coating levels of 0.5%, 1% and 2%. These data indicate potential improvements in selected aggregate properties, but they represent a separate dosage series and should not be merged with the 0–8% table. 4. For the three Marshall binder contents tested, the maximum reported stability is 2627 kg at 8.5% bitumen. Stability decreases to 2410 kg at 9.0%, while the plotted flow value increases with binder content. 5. The optimum bitumen content cannot be independently confirmed because the numerical contents of the OBC parameter table are not available in readable form in the report. 6. Most importantly, the project report states that the final dense bituminous mix prepared with the selected polymer-coated aggregates did not satisfy the cited IRC requirements. The present findings therefore do not establish specification-compliant pavement mix performance.
[1] H. Laldintluanga, Zorinkima, and R. Ramhmachhuani, “Enhancing the durability of bituminous concrete using plastic waste on soft rock aggregates,” Polymers, vol. 18, no. 7, Art. no. 813, 2026, doi: 10.3390/polym18070813. [2] X. Wu, E. Jusli, W. Anggraini, R. P. Jaya, and X. Zhang, “Performance and environmental impacts of waste plastic-modified asphalt pavement: A comprehensive review,” Cleaner Materials, vol. 18, Art. no. 100357, 2025, doi: 10.1016/j.clema.2025.100357. [3] O. Matre, V. Dhanuskar, and P. Sawarkar, “Utilization of waste plastics in road construction: Enhancing aggregate and bitumen properties for sustainable pavement development,” Advances in Transdisciplinary Engineering, 2025, doi: 10.3233/ATDE251274. [4] M. L. Pallavi, S. Dey, G. T. N. Veerendra, S. S. A. B. Padavala, and A. V. P. Manoj, “Optimizing the bituminous pavement constructions with waste plastic materials improved the road constructions performance and their future applications,” AI in Civil Engineering, vol. 3, Art. no. 16, 2024, doi: 10.1007/s43503-024-00035-5. [5] R. P. Ashish, P. Kumar, S. Sreeram, A. Xu, X. Chandrasekar, P. Jagadeesh, A. Adwani, and R. K. Padhan, “Closing the loop: Harnessing waste plastics for sustainable asphalt mixtures—A comprehensive review,” Construction and Building Materials, vol. 400, Art. no. 132858, 2023, doi: 10.1016/j.conbuildmat.2023.132858. [6] R. Xiao, Z. Shen, P. Polaczyk, and B. Huang, “Thermodynamic properties of aggregate coated by different types of waste plastic: Adhesion and moisture resistance of asphalt-aggregate systems,” Journal of Materials in Civil Engineering, vol. 35, no. 8, 2023, doi: 10.1061/JMCEE7.MTENG-15679. [7] M. A. Rabby, M. Alam, T. K. Ray, and J. Bari, “Reusing waste plastics in aggregate for road construction,” in Proc. Int. Airfield and Highway Pavements Conf., 2023, doi: 10.1061/9780784484906.012. [8] A. Noor and M. A. U. Rehman, “A mini-review on the use of plastic waste as a modifier of the bituminous mix for flexible pavement,” Cleaner Materials, vol. 4, Art. no. 100059, 2022, doi: 10.1016/j.clema.2022.100059. [9] S. Karmakar and T. K. Roy, “Influence of plastic waste on chemical and mechanical properties of modified bitumen used in the bituminous mix for flexible pavement,” Journal of Materials in Civil Engineering, vol. 33, no. 2, Art. no. 04020440, 2021, doi: 10.1061/(ASCE)MT.1943-5533.0003545. [10] S. L. Hake, R. M. Damgir, and P. R. Awsarmal, “Utilization of plastic waste in bitumen mixes for flexible pavement,” Transportation Research Procedia, vol. 48, pp. 3779–3785, 2020, doi: 10.1016/j.trpro.2020.08.041. [11] S. G. Dhundalwar, A. Moon, V. C. Patle, and S. K. Jaiswal, “Use of plastic waste in bituminous road construction,” pp. 3637–3644, 2017. [12] P. Singh and R. R. K. Yadav, “Effect of plastic waste on properties of road aggregate,” IJIRST—International Journal of Innovative Research in Science and Technology, vol. 2, no. 11, pp. 2012–2015, 2016.
Publication Date
11/13/2026
Peer Review Type
Double-Blind Peer Review
Review Rounds: 2
Documents
Article Views
0
Total views since publication
PDF Downloads
4
Total downloads since publication
Geographic Reach
5
Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.
Plagiarism Screening
This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.
Conflict of Interest
The authors declare no conflict of interest related to this research work.
Funding Information
No funding information available for this research.
Related research in the same subject area
Loading similar articles...