Loading article...
Loading article...
Stream/Area:
-
Subject:
-
Paper ID:
IJSREM68922
Volume:
10 |
11 |
Nov 2026
Pages:
1-10
Publication Frequency:
Monthly (12 issues per year)
License:International Journal of Scientific Research in Engineering and Management follows the Creative Commons Attribution 4.0 (CC BY 4.0) License, allowing free use and distribution with proper attribution.
Civil Engineering
D.Y. Patil Technical Campus
Cement-free paver blocks bound with melted waste plastic can turn two problem waste streams, post-consumer plastic and spent foundry sand (SFS), into pedestrian-grade paving, but the evidence is thin and the strength data need verification. This review synthesizes about 30 sources on paver blocks made with alternative aggregates, fibres, industrial by-products and geopolymer binders, and examines one thermoplastic route in detail: waste low-density polyethylene (LDPE) melted as a binder around SFS at a 4:1 sand-to-plastic mass ratio. Across the literature, partial replacement of cement or aggregate, typically at 15% to 60%, preserves acceptable strength, while complete removal of cement and water curing is rarely attempted. In the LDPE–SFS case reviewed, blocks weighed about 2.90 kg against 4.50 kg for OPC concrete, a reduction of about 35.5%, and carried a lower crushing load (350 against 480, in the units reported). The review flags open issues: inconsistent strength units, leaching, fire and UV behaviour, softening above about 80°C, and the lack of standardised testing. It closes with priorities for scale-up.
KEYWORDS
1. Published paver block research mostly substitutes part of the cement or aggregate in water-cured concrete. Fibres, industrial by-products and geopolymers each have documented benefits, but few studies remove OPC and water curing together. 2. Waste LDPE melted around SFS at 4:1 by mass is a feasible cementless route, needing only a steel drum, hand tools and no curing [31]. 3. The resulting blocks are about 35.5% lighter than OPC concrete blocks (2.90 kg against 4.50 kg) and fail in a ductile way, which lowers handling effort and transport energy. 4. Their crushing load is lower than concrete's, and the reported strength figures cannot yet be read as pavement-grade stress. Use should be limited to non-traffic pedestrian areas until verified. 5. With strength reporting, thermal behaviour, leaching and life-cycle impacts resolved, the approach could cut municipal plastic waste, reuse foundry sand and conserve natural aggregate.
[1] M. A. Raghatate, "Use of plastic bags in concrete," International Journal of Advanced Engineering Research and Studies, vol. 1, no. 3, pp. 121–123, 2012. [2] S. Parihar and H. R. Kumavat, "Recycled plastic as aggregate in paver blocks," International Journal of Engineering Research & Technology, vol. 4, no. 5, pp. 412–415, 2015. [3] J. Brožovský, O. Matějka, and P. Martinec, "Concrete interlocking paving blocks compression strength determination using non-destructive methods," Proceedings of the 8th NDT Conference, pp. 91–97, 2005. [4] T. C. Ling, H. M. Nor, and R. Mudiyono, "The effect of cement and water cement ratio on concrete paving block," Regional Postgraduate Conference on Engineering and Science, pp. 89–92, 2006. [5] P. Nanda, A. K. Das, and S. Mohanty, "Stone crusher dust replacement in paver blocks," Journal of Civil Engineering Solutions, vol. 2, pp. 45–50, 2010. [6] G. Tapkire, S. Parihar, P. Patil, and H. R. Kumavat, "Recycled plastic used in concrete paver block," International Journal of Research in Engineering and Technology, vol. 3, no. 9, pp. 33–38, 2010. [7] K. Kalingarani, H. Devudu, M. Jegan Ram, and V. Sriramkumar, "Development of paver blocks from industrial wastes," IOSR Journal of Mechanical and Civil Engineering, pp. 12–17, 2012. [8] A. Vaz, R. Silva, and M. Fernandes, "Geopolymer concrete paver blocks production utilizing industrial by-products," International Journal of Advanced Research in Science, vol. 2, pp. 102–108, 2012. [9] C. M. Ravikumar, H. Anilkumar, M. D. Prashanth, and V. Reddy, "Experimental studies on iron-ore tailing based interlocking paver," International Journal of Earth Sciences and Engineering, vol. 5, no. 3, pp. 501–504, 2012. [10] R. Thakur, S. Sharma, and P. Patel, "Nylon fiber influence on paver block strength," International Journal of Engineering Sciences & Innovative Technology, vol. 2, no. 4, pp. 88–94, 2013.
Publication Date
11/13/2026
Peer Review Type
Double-Blind Peer Review
Review Rounds: 2
Documents
Article Views
0
Total views since publication
PDF Downloads
2
Total downloads since publication
Geographic Reach
5
Digital Preservation: This article is permanently archived on Zenodo and complies with all data preservation standards across major indexing platforms.
Plagiarism Screening
This manuscript has been checked for plagiarism using TurnitinPlagiarismChecker software.
Conflict of Interest
The authors declare no conflict of interest related to this research work.
Funding Information
No funding information available for this research.
Related research in the same subject area
Loading similar articles...